AIRLESS ADVANCED

Model no. 1814
Tests on finished products, Internal hydrostatic and quick burst test equipment

Professionally pressure tested

As a logical development of the successful Airless ProfessionalLine Model 1720, IPT is launching the Model 1814: a new time-dependent internal pressure and burst testing device for use in accordance with ISO 1167, ASTM D 1598, and ASTM D 1599. Its completely redesigned modular construction offers improved accessibility, providing maximum user-friendliness and ease of maintenance. The innovative control electronics allow test pressures of up to 200 bar to be precisely regulated. The Model 1814 can be integrated into the new professional IPT DataLogging® Version 7 testing software.

Standards

Keine Standards gefunden

ISO 1167
ASTM D 1598
ASTM D 1599

Downloads

Features and Functionality

A maximum of nine airless modules can be installed in the 1814 installation frame. A maximum of 45 test stations for time-dependent pressure tests or 12 test stations for burst pressure tests can be installed.

Up to four extension cabinets (without their own pressurised water supply) can be connected to the installation frame. The configuration varies depending on requirements, with a maximum of up to 60 test stations per extension rack for internal pressure tests or a maximum of 16 test stations for burst pressure tests.

In addition to the modules, the rack contains the pressurised water supply for generating the pre-pressure, the power supply and a status display.

Pressurised water supply

The pipe tester is supplied with the required high-pressure water via the integrated pressurised water supply (6, 12 or 24 litres/min.) or a pressurised water supply from existing frames (base or expansion units). The pressurised water supply consists of:

Water inlet with water filter and pre-pressure monitoring
Pressure vessel (buffer tank): Prevents pressure peaks and temporarily increases the water supply capacity.
Controller: For controlling the high-pressure pump and monitoring the system pressure.

Module and controller

For each module, a controller (microprocessor control) individually controls and regulates the pressure of the individual stations. For pressure control, each station has two solenoid valves and a pressure transducer. The solenoid valve MV1 regulates the pressure build-up. The solenoid valve MV2 is used for pressure reduction and pressure relief at the end of the test.

Options

Precision pressure measurement instrument 1817 (master gauge): An external precision pressure measurement instrument can be connected via a needle valve bar in order to check the test pressure before or during a test. The test pressures of the individual stations can be easily checked with the master gauge. They can then be readjusted if necessary if a pressure measurement accuracy of 0.3% of the final value of the pressure transducer does not appear to be sufficient.

Periphery and Complementary

HAT-Tester

Model no. 1821

Tests on finished products
Internal hydrostatic and quick burst test equipment

This innovative testing procedure ensures dependable assessment of structural integrity and connection strength, even for pipe sizes up to DN 630. Available from July!

Standards

ISO/CD 19521-1
ISO/CD 19521-2

TEST TANKS

Model no. 1830 - 1840

Tests on finished products
Internal hydrostatic and quick burst test equipment

The creep internal pressure test is a test method for determining the strength of thermoplastic pipes. Available from July!

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

TEST BATHS

Model no. 1751 - 1757

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Test oven

Model no. 1662/1674

Tests on finished products
Internal hydrostatic and quick burst test equipment

The test ovens are specially designed for testing thermoplastic pipes and fittings.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Test oven

Model no. 1776

Tests on finished products
Internal hydrostatic and quick burst test equipment

The test ovens are specially designed for testing thermoplastic pipes and fittings.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

BURST CHAMBER FOR FITTINGS

Model no. 1618

Tests on finished products
Internal hydrostatic and quick burst test equipment

For burst pressure tests up to 200 bar on plastic fittings with inside diameter up to 160 mm with 3-dimensional loading.

Standards

ASTM D 1599

PIPE SAW

Model no. 1625

Sample preparation

To produce test specimens for creep pressure tests, falling weight tests, heat reversion tests, or tests with the methylene chloride tester, the pipe lengths must be cut to standard dimensions.

Standards

ISO 1167
ISO 11173
ISO 2505
ISO 3127
ISO 9852

END CLOSURES

Model no. 1810

Tests on finished products
Internal hydrostatic and quick burst test equipment

The end clolsures model 1810 are designed for the quick sealing of plastic pipes up to DN 2700 mm and are characterised by easy handling – simple, brilliant and inexpensive. Available from July!

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

QUIX END CLOSURES 100 BAR

Model no. 1732/1733

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes to constant hydrostatic internal pressure at a constant ambient temperature.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

END CLOSURES WITH TIE ROD ISO

Model no. 1685

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes when exposed to constant hydrostatic internal pressure at

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Test Data Management Software IPT DataLogging®V7

Model no. 1780

Software

IPT DataLogging®V6

Model no. 1780

Software

The product family

For peak performance

AIRLESS PROFESSIONAL LINE

Model no. 1720

Tests on finished products
Internal hydrostatic and quick burst test equipment

The purpose of this tester is to apply and maintain the correct hydrostatic pressure for internal pressure creep tests. Bursting pressure tests can also be optionally performed. Up to 9 modules – equivalent to 45 stations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Precise and consistent

AIRLESS BLUELINE

Model no. 1774

Tests on finished products
Internal hydrostatic and quick burst test equipment

For mid-level testing demands, the Airless BlueLine ensures pressure control at maximum adjustment precision and consistency.

Up to 6 modules – equivalent to 30 stations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Flexible

Airless LightLine

Model no. 1790

Tests on finished products
Internal hydrostatic and quick burst test equipment

The 1790 Airless LightLine full set, with its five pressure stations and test bath, provide a simple all-in-one solution. The operation, evaluation of the results and clear visualization is done via a laptop.

Standards

ISO 1167
ASTM D 1598

To get started

AIRLESS COMPACTLINE

Model no. 1799

Tests on finished products
Internal hydrostatic and quick burst test equipment

The 1799 full set combines five pressure stations and a test bath in a single housing.

Standards

ISO 1167

AIRLESS BASICLINE

Model no. 1785

Tests on finished products
Internal hydrostatic and quick burst test equipment

Our BasicLine product version has been specifically developed for flexible laboratory applications where compact design and mobility are key priorities. The system is small, space-saving, and easily movable – making it ideal for laboratories with limited space or changing locations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599