Our products and solutions

Product Categories

Standards

AIRLESS PROFESSIONAL LINE

Model no. 1720

Tests on finished products
Internal hydrostatic and quick burst test equipment

The purpose of this tester is to apply and maintain the correct hydrostatic pressure for internal pressure creep tests. Bursting pressure tests can also be optionally performed. Up to 9 modules – equivalent to 45 stations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

AIRLESS ADVANCED

Model no. 1814

Tests on finished products
Internal hydrostatic and quick burst test equipment

The purpose of this tester is to apply and maintain the correct hydrostatic pressure for internal pressure creep tests.

Available from July!

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

AIRLESS BLUELINE

Model no. 1774

Tests on finished products
Internal hydrostatic and quick burst test equipment

For mid-level testing demands, the Airless BlueLine ensures pressure control at maximum adjustment precision and consistency.

Up to 6 modules – equivalent to 30 stations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

BURST TESTER FOR PIPES WITH LARGE DIAMETERS

Model no. 1718

Tests on finished products
Internal hydrostatic and quick burst test equipment

The burst pressure tester for pipes with large diameters is a further milestone for burst tests on large-volume samples.

Standards

ASTM D 1599

Airless LightLine

Model no. 1790

Tests on finished products
Internal hydrostatic and quick burst test equipment

The 1790 Airless LightLine full set, with its five pressure stations and test bath, provide a simple all-in-one solution. The operation, evaluation of the results and clear visualization is done via a laptop.

Standards

ISO 1167
ASTM D 1598

AIRLESS COMPACTLINE

Model no. 1799

Tests on finished products
Internal hydrostatic and quick burst test equipment

The 1799 full set combines five pressure stations and a test bath in a single housing.

Standards

ISO 1167

AIRLESS BASICLINE

Model no. 1785

Tests on finished products
Internal hydrostatic and quick burst test equipment

Our BasicLine product version has been specifically developed for flexible laboratory applications where compact design and mobility are key priorities. The system is small, space-saving, and easily movable – making it ideal for laboratories with limited space or changing locations.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

TEST BATHS

Model no. 1751 - 1757

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

TEST TANKS

Model no. 1830 - 1840

Tests on finished products
Internal hydrostatic and quick burst test equipment

The creep internal pressure test is a test method for determining the strength of thermoplastic pipes. Available from July!

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

TEST TANK

Model no. 1678

Tests on finished products
Internal hydrostatic and quick burst test equipment

The IPT test tank for internal pressure creep testing is characterised by state-of-the-art technology, maximum safety and optimised heating power with very low energy consumption.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

CHILLER

Model no. 1765

Tests on finished products
Internal hydrostatic and quick burst test equipment

The main field of application for the 1765 series cooling units is to maintain the water temperature in our test tanks at 20°C.

Standards

ISO 1167
ISO 10508
ISO 19893
ASTM D 1598
ASTM D 1599
EN 12293

HAT-Tester

Model no. 1821

Tests on finished products
Internal hydrostatic and quick burst test equipment

This innovative testing procedure ensures dependable assessment of structural integrity and connection strength, even for pipe sizes up to DN 630. Available from July!

Standards

ISO/CD 19521-1
ISO/CD 19521-2

Test oven

Model no. 1662/1674

Tests on finished products
Internal hydrostatic and quick burst test equipment

The test ovens are specially designed for testing thermoplastic pipes and fittings.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Test oven

Model no. 1776

Tests on finished products
Internal hydrostatic and quick burst test equipment

The test ovens are specially designed for testing thermoplastic pipes and fittings.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

BURST CHAMBER FOR FITTINGS

Model no. 1618

Tests on finished products
Internal hydrostatic and quick burst test equipment

For burst pressure tests up to 200 bar on plastic fittings with inside diameter up to 160 mm with 3-dimensional loading.

Standards

ASTM D 1599

BURST CHAMBER

Model no. 1623

Tests on finished products
Internal hydrostatic and quick burst test equipment

For burst pressure tests up to 200 bar on injection moulded fittings with diameters 16 – 110 mm.

Standards

ASTM D 1599

END CLOSURES

Model no. 1810

Tests on finished products
Internal hydrostatic and quick burst test equipment

The end clolsures model 1810 are designed for the quick sealing of plastic pipes up to DN 2700 mm and are characterised by easy handling – simple, brilliant and inexpensive. Available from July!

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

QUIX END CLOSURES 100 BAR

Model no. 1732/1733

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes to constant hydrostatic internal pressure at a constant ambient temperature.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

QUIX END CLOSURES 200 BAR

Model no. 1735/1736

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes to constant hydrostatic internal pressure at a constant ambient temperature.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

END CLOSURES WITH TIE ROD ISO

Model no. 1685

Tests on finished products
Internal hydrostatic and quick burst test equipment

The internal pressure creep test is a test procedure for determining the strength of thermoplastic pipes when exposed to constant hydrostatic internal pressure at

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

END CLOSURES FOR BURST TESTS

Model no. 1634

Tests on finished products

For fittings with a diameter of up to 110 mm, suitable for the IPT burst chamber model 1623. The fittings are only for use in a burst chamber.

Standards

ASTM D 1599

END CLOSURES FOR FLOOR HEATING

Model no. 1280

Tests on finished products

Model 1280 heating pipe closures are used to close underfloor heating pipes, even at high test temperatures of up to 130°C.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

MOUNTING AID

Model no. 1684

Tests on finished products

The mounting aid for pipe samples is designed to facilitate the mounting and dismounting of endclosures for instance (models 1810 and 1784).

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

TEST TANK ACCESSORIES

Model no. 1751 - 1757

Tests on finished products

Different accessories are required for the various test methods used to determine the strength of thermoplastic pipes.

Standards

ISO 1167
ASTM D 1598
ASTM D 1599

Pulsator

Model no. 1796/1797

Tests on finished products
Additional testing equipment

The IPT servo pulsator was specially developed to determine the behaviour of pipes and pipe connections during pressure surge testing.

Standards

ISO 19892
EN 12295
DVGW W 543

Pulsator

Model no. 1766

Tests on finished products

For carrying out dynamic internal pressure tests on pipes and pipe components with sinusoidal or linear pressure curves up to 400 bar.

Standards

EN 12295
DVGW W 543
DVGW W 534

TEMPERATURE CYCLING TEST UNIT

Model no. 1769

Tests on finished products
Additional testing equipment

The temperature cycling test device is used to evaluate the resistance of joints in thermoplastic piping systems to temperature change stresses. Temperatures of up to 114 °C enable realistic testing conditions to ensure safety and reliability.

Standards

ISO 10508
DVGW W 542
DVGW W 543
DVGW W 534

TEMPERATURE CYCLING TEST UNIT

Model no. 1770

Tests on finished products
Additional testing equipment

The temperature change tester allows you to determine the resistance of connections for pipe systems with rigid or flexible thermoplastic pipes to temperature changing stress.

Standards

DVGW W 534
DVGW W 543
DVGW W 542
ISO 19892
EN 12293

TEMPERATURE CYCLING TESTING DEVICE

Model no. 1777

Tests on finished products
Additional testing equipment

The temperature cycling test device evaluates the resistance of joints in thermoplastic piping systems with rigid or flexible pipes to temperature change stresses. It is designed for systems used in pressurized hot and cold water applications.

Standards

ISO 10508
EN 12293
DVGW W 542
DVGW W 543
DVGW W 534

TEMPERATURE CYCLING TESTING DEVICE (unpressurised)

Model no. 1268

Tests on finished products
Additional testing equipment

This test determines the resistance of pipe system connections to thermal cycling

Standards

EN 1055

LOAD BOX

Model no. 1772

Tests on finished products
Additional testing equipment

The load box is an extension of the temperature cycling tester for waste water.

Standards

ISO 13260

COIL PRESSURE TESTER

Model no. 1656

Tests on finished products

Pressure test unit for test leakage on plastic pipes in series production up to max. diameter D 32 mm and a max. sample lenght of 500 meters.

Standards

UNI 9349

OXYGEN TESTER

Model no. 1679

Tests on finished products

The oxygen increase is measured in a system of which the test piece forms part.

Standards

ISO 17455

Test chamber for leak testing

Model no. 1730

Tests on finished products
Internal hydrostatic and quick burst test equipment

Whether in quality assurance, laboratory environments, or production – the 1730 delivers reproducible, standards-compliant results and ensures maximum process reliability.

Standards

ISO 3503
DVGW W 543

RING STIFFNESS TESTERS

Model no. 1663/1669

Tests on finished products
Additional testing equipment

With the model 1663 and 1669 testers, the ring stiffness, ring flexibility and creep behaviour of thermoplastic pipes can be determined.

Standards

ISO 9967
ISO 9969
ISO 13968
DIN 16961-2
ASTM D 2412

COMBI TEST STAND

Model no. 1771

Tests on finished products
Additional testing equipment

The combi test stand is used to perform leak tests on pipe connections.

Standards

ISO 13254
ISO 13259

COMBI TEST STAND

Model no. 1351

Tests on finished products
Additional testing equipment

The combi test stand 1351 is used to carry out leak tests on waste water pipe systems in the diameter range DN 40 to DN 400.

Standards

ISO 13254
ISO 13259

METHYLENE CHLORIDE TESTER

Model no. 1800

Tests on finished products
Additional testing equipment

The methylene chloride tester model 1800 is used for material testing of extruded profiles and pipes made of rigid PVC (e.g. pipes) in accordance with ISO 9852 or EN 580.

Standards

ISO 9852

Chlorine Testing Device

Model no. 1802

Tests on finished products
Additional testing equipment

The Chlorine Testing Device Model 1802 is a modern system for long-term testing of plastic pipes under chlorinated conditions.

Standards

NSF P 171
ASTM F 1281
ASTM F 1282
ASTM F 2330
ASTM F 2262
ASTM F 2263
ASTM F 2023

BULK DENSITY TESTER DIN

Model no. 1132

Tests on raw materials

The device for determining bulk density is a simple and reliable option for checking the uniform structure of moulding compounds.

Standards

ISO 60
ASTM D 1895

POURABILITY TESTER

Model no. 1326

Tests on raw materials

Poor plastic flow properties can cause the flow of material in the funnel of the processing machine to slow down and even stop.

Standards

ISO 6186
ASTM D 1895

MFR/MVR TESTER

Model no. 1709

Tests on raw materials

The 1709 MFR/MVR tester is used to determine the melt flow rate of thermoplastics.

Standards

ISO 1133
ASTM D 1238

CARBON BLACK CONTENT TESTER

Model no. 1398

Tests on raw materials

Standards stipulate the determination of the carbon black content of polyolefins and/or also the residue on ignition of carbon blacks.

Standards

ISO 6964
ASTM D 1895

ESCR TESTER

Model no. 1692

Tests on raw materials

ASTM D1693 is a test method for determining environmental stress crack resistance (ESCR) in ethylene plastics.

Standards

ASTM D 1963

TENSILE CREEP TESTER

Model no. 1598

Tests on finished products
Tests on raw materials

The tensile creep tester is used to determine the stress crack resistance of samples with a circumferential notch (FNCT – Full Notch Creep Test) under media influence.

Standards

ISO 16770

TENSILE CREEP TESTER

Model no. 1727

Tests on finished products
Tests on raw materials

The tensile creep tester is intended for determining the resistance of plastic samples during a tensile creep test.

Standards

ISO 16770

TENSILE CREEP TESTER

Model no. 1719

Tests on finished products
Tests on raw materials

The tensile creep tester is used to determine the stress crack resistance of samples with a circumferential notch (FNCT – Full Notch Creep Test) under media influence.

Standards

ISO 16770

Point Load Testing Device

Model no. 1775

Tests on finished products
Additional testing equipment

The resistance of pipes to slow crack growth under external point loads can be determined using a point load test.

Standards

PAS 1075

UNIT FOR DETERMINATION OF THE DEGREE OF CROSSLINKING

Model no. H3006

Tests on finished products
Additional testing equipment
Tests on raw materials

ISO 10147 stipulates that test samples made from crosslinked polyethylene (PE-X) must be stored in a specified, boiling solvent for a specific period of time and that the percent by weight of insoluble material is then measured.

Standards

ISO 10147
ASTM D 2765 Method B
DIN 16892

VICAT/HDT TESTER

Model no. H3013

Tests on finished products
Additional testing equipment

The tester is used to determine the Vicat softeningtemperature and the heat resistance temperature under load for plastics and thermoplastics.

Standards

ISO 2507
ISO 306
ISO 75
ASTM D 1525
ASTM D 648

UNIVERSAL TENSILE TESTER

Model no. H3016

Tests on finished products
Additional testing equipment

The universal tensile tester is used for performing tension, pressure or bending tests. The classic application is the tensile test. This involves subjecting a sample to an increasing tensile load until it breaks.

Standards

ISO 6259
ASTM D 638

FALLING WEIGHT TESTER

Model no. 1713

Tests on finished products
Impact and Drop-Test-Equipment

The falling weight tester is used to determine the external impact resistance of thermoplastic pipes using the staircase or round-the-clock method.

Standards

ISO 11173
ISO 3127
ASTM D 2444

ZERO°C TEST TANK

Model no. 1763

Sample preparation

For conditioning samples for impact and drop tests with a water depth of up to 1,000 mm.

Standards

ISO 11173
ISO 3127
ASTM D 2444
EN 477

IMPACT DROP TESTER FOR PACKAGING

Model no. 1654

Tests on finished products
Impact and Drop-Test-Equipment

You can test packaging of varying shapes and sizes for impact stress after free fall using IPT’s drop testers.

Standards

ASTM D 2463

IMPACT DROP TESTERS FOR PACKAGING

Model no. 1529/1543

Tests on finished products
Impact and Drop-Test-Equipment

You can test packaging of varying shapes and sizes for impact stress after free fall using IPT’s drop testers. The packaging can be tested with its content and may consist of cans, barrels and boxes.

Standards

ASTM D 2463

IMPACT DROP TESTER FOR PACKAGING

Model no. 1523

Tests on finished products
Impact and Drop-Test-Equipment

You can test packaging of varying shapes and sizes for impact stress after free fall using IPT’s drop testers.

Standards

ASTM D 2463

IMPACT DROP TESTER FOR WINDOWS PROFILES

Model no. 1572

Tests on finished products
Impact and Drop-Test-Equipment

With the increasing popularity of plastic window and door profiles, the demands on the material have also increased in recent years, particularly in terms of load-bearing capacity and durability.

Standards

EN 477
RAL GZ 716/1

RCP-S4-TESTER

Model no. 1671

Tests on finished products
Tests on raw materials

The RCP-S4 tester model 1671 is developed to perform tests on pipes up to DN 630.

Standards

ISO 13477

RCP-S4-TESTER

Model no. 1629

Tests on finished products
Tests on raw materials

The tester model 1629 is used to determine the resistance of plastic pipes to rapid crack propagation under internal overpressure and low temperatures in accordance with ISO 13477 (Rapid Crack Propagation).

Standards

ISO 13477

Marking gauge

Model no. 1291

Sample preparation

To determine the change in length as a result of warm storage, the marking gauge can be used to mark precise parallel circles on the outer surface of pipe segments with a diameter of up to 400 mm.

Standards

ISO 2505
NFT 54-047

Spiralrohrschneider 1411

Model no. 1411

Sample preparation

To determine the delamination between the different material layers of cross-linked polyethylene pipes, samples up to a diameter of 32 mm can be produced.

Standards

ASTM F 1281
ASTM D 1282

CONE TESTER

Model no. 1680

Tests on raw materials

For the preparation of a sample for determining resistance to slow crack growth.

Standards

ISO 13480

PIPE SAW

Model no. 1625

Sample preparation

To produce test specimens for creep pressure tests, falling weight tests, heat reversion tests, or tests with the methylene chloride tester, the pipe lengths must be cut to standard dimensions.

Standards

ISO 1167
ISO 11173
ISO 2505
ISO 3127
ISO 9852

CNC TEST BAR MILLING MACHINE

Model no. 1812

Sample preparation

The CNC test bar milling machine enables bar-shaped plastic samples to be produced for tension, pressure, bending and flexural impact tests in accordance with a wide range of standards.

Standards

ISO 527
ISO 6259
ASTM D 638
ISO 179
ISO 180
ISO 16770
ASTM D 1822

CNC TEST BAR MILLING MACHINE

Model no. 1843

Sample preparation

The CNC test bar milling machine enables bar-shaped plastic samples to be produced for tension, pressure, bending and flexural impact tests in accordance with a wide range of standards.

Standards

ISO 527
ISO 6259
ASTM D 638
ISO 179
ISO 180
ISO 16770
ASTM D 1822

NOTCH MILLING MACHINE

Model no. 1653

Tests on raw materials
Sample preparation

ISO 13479 is a test method for determining the resistance to slow crack growth of polyolefin pipes for transporting fluids.

Standards

ISO 13479

LABORATORY GRANULATOR

Model no. 1665

Sample preparation

The laboratory granulator was developed for the production of granulates from plastic pipe slices or plastic sheets, for example for the determination of MFR/MVR values.

Standards

ISO 1133
ISO 1183
ASTM D 1505

MOTORISED NOTCHING DEVICE FOR FNCT

Model no. 1808

Sample preparation

The newly developed Model 1808 electric notching device from IPT is designed for fast and precise notching of test bars for FNCT testing in accordance with ISO 16770.

Standards

ISO 16770

WALL THICKNESS MEASURING UNIT

Model no. 1049

Measuring devices

The wall thickness measuring unit model 1049 allows the wall thickness of pipes to be measured to a high degree of accuracy.

Standards

ISO 3126

ANALYTICAL BALANCE

Model no. H3000

Tests on raw materials
Sample preparation

The analytical balance is required in every test laboratory. It is used to precisely determine important values such as MFR, carbon black content, K-value, degree of crosslinking, OIT, volatile components, water absorption and similar.

Standards

ISO 1133
ISO 1628-2
ISO 62
ISO 6964
EN 12099

LABORATORY SIEVING MACHINE

Model no. H3001

Tests on raw materials

The digital laboratory sieving machine allows you to easilyand accurately determine the fineness and particle size distribution of all dust-like, powdery or granular products.

Standards

ISO 2395
ISO 3310
ISO 565
DIN 66165
ASTM D 1921
ASTM E 11

UNIT FOR DETERMINATION OF DENSITY

Model no. H3002

Tests on raw materials

This tester is used to determine the density of plastics according to the buoyancy method. The complete set consists of a beaker, thermometer, glass plummet for determining the liquid density, submerged filter and submerged contactor.

Standards

ISO 1183
ASTM D 792

DSC MEASURING DEVICE FOR OIT MEASUREMENTS

Model no. H3003-0056

Tests on raw materials

The device operates according to the heat flow principle. In this method, a sample and a reference are subjected to a controlled temperature programme (heating, cooling or isothermal).

Standards

ISO 11357-6

DSC MEASURING DEVICE FOR OIT MEASUREMENTS

Model no. H3003-0037/H3003-0038

Tests on raw materials

Dynamic differential calorimeter for determining the oxidation induction time for plastic piping and protective pipe systems, as well as fittings made of polyolefins.

Standards

ISO 11357-6

VOLATILE CONTENT TESTER

Model no. H3004

Tests on raw materials

The unit for determination of volatile matter is designed for determining the content of material volatile at 105 °C in polyethylene (PE) piping materials. This method is applicable to moulding and extrusion materials. It also can be applicable to components in PE piping systems.

Standards

EN 12099

Prüfgerät zur Bestimmung der Wasseraufnahme H3005

Model no. H3005

Tests on raw materials

Standards

ISO 62
ASTM D 570

K VALUE TESTER

Model no. H3008

Tests on raw materials

The test is used to determine the K value of PVC in a diluted solution at a temperature of 25 °C. The K value provides information for characterising the polymerisation of VC polymers.

Standards

ISO 1628-2

ROTATIONAL MICROTOME

Model no. H3009

Sample preparation

The microtome is used to cut very thin slices from a sample material in order to subsequently assess the degree of pigment and carbon black dispersion in polyolefin pipes and fittings.

Standards

ISO 18553
ASTM D 5596

CIRCULATING AIR OVEN

Model no. H3014-0013

Sample preparation

The circulating air oven is used to condition specimens according to the dimensional change of pipes and also as a drying oven (e.g. for determining the degree of crosslinking, water absorption, etc.).

Standards

ISO 2505

CIRCOMETER

Model no. H3017

Measuring devices

Circometers are the easiest way to determine the outside diameter of pipes ranging from 15 to 3100 mm.

Standards

ISO 3126
ASTM D 2122

PENDULUM IMPACT TESTER

Model no. H3018

Tests on finished products
Impact and Drop-Test-Equipment

The pendulum impact tester enables testing across the entire spectrum of plastic impact testing, Charpy, Izod, impact and Dynstat in accordance with ISO and ASTM standards.

Standards

ISO 179
ISO 180
ISO 8256-A
ASTM D 256
ASTM D 4812
ASTM D 6110
DIN 53435

OUTSIDE CALIPER INSIDE CALIPER

Model no. H3019

Measuring devices

The outside caliper enables the wall thickness of pipes and fittings to be measured quickly and easily. With the help of the inside caliper, an internal three-point measurement can be carried out quickly and easily.

Standards

ISO 3126

Shore-Härte-Prüfgerät H3020

Model no. H3020

Tests on raw materials

Shore hardness describes a material’s resistance to the penetration of an indenter under a defined force and is expressed on a scale from 0 to 100.

Standards

ISO 7619
ISO 868
ASTM D 2240

MOISTURE CONTENT UNIT

Model no. H3021-0002

Tests on raw materials

The tester for determining moisture content is used to quickly and reliably determine the material moisture content of liquid, paste-like and solid substances according to the thermogravimetric method.

Standards

ISO 585
EN 12118

MICROSCOPE AND DIGITAL CAMERA

Model no. H3022

Tests on raw materials

According to the method for the assessment of the degree of pigment and carbon black dispersion in polyolefin pipes, fittings and compounds, a microscope is required to examine the particles and agglomerates in the test sample.

Standards

ISO 18553
ASTM D 5596

MICROMETER

Model no. H3023

Measuring devices

The micrometer (also known as a micrometer gauge) is used to determine thickness.

Standards

ISO 3126

DIGITAL VERNIER CALIPERS

Model no. H3024

Measuring devices

Vernier calipers are the simplest way to measure the ovality of pipes.

Standards

ISO 3126

COOLING CHAMBER

Model no. H3026

Sample preparation

The walk-in cooling chamber is used to condition specimens to the preset temperature.

Standards

ISO 11173
ISO 13477
ISO 3127
ASTM D 2444

MANUAL CUTTING PRESS

Model no. H3031-0100/0101

Sample preparation

The extra-strong manual cutting presses in the H3031-0100/-0101 series are suitable for preparing test samples from various materials, such as rubber, foam, films and other plastics.

Standards

ISO 527
ISO 6259

MANUAL NOTCH MILLING MACHINE

Model no. H3047

Sample preparation

The manual notch milling machine is used to quickly and precisely produce U-shaped or V-shaped notches on standardised plastic test samples.

Standards

ISO 179
ISO 180

Test Data Management Software IPT DataLogging®V7

Model no. 1780

Software

IPT DataLogging®V6

Model no. 1780

Software